This is our older short-reference index. For full illustrated explanations, use the new lessons on the main Decoder page.
THE SOUND QUESTION · FREE LEARNING TOOL
Decode the numbers.
Understand the sound.
This is one stop along the sound journey. Find out what the numbers on amplifier and speaker listings mean for music, what might matter when buying, and which differences are simply a matter of taste. Start with everyday explanations, then go deeper when you're curious.
PART ONE · AMPLIFIERS
What do amplifier numbers tell you?
These are the kinds of claims you might encounter when shopping for an amplifier. Open any row for an explanation that starts with the music, not the mathematics.
Power per channel80 watts per channel into 8 Ω
In everyday language: How much power the amplifier can send to one speaker under the conditions used for the test.
What might you notice when listening?
It can help the amplifier handle demanding parts of a song, like a sudden heavy drum hit, without running out of room to get louder cleanly.
Should this affect what you buy?
More watts can be useful, but doubling the watts does not make the music sound twice as loud. Check the speaker type and the test conditions too.
Go deeper: the technical explanation
Power ratings depend on the speaker load, the pitch range tested, the amount of distortion allowed, how long the test lasts, and how many channels are working. For an ideal resistor, average power equals RMS volts times RMS amps.
Power with a more demanding speaker120 watts into 4 Ω
In everyday language: A power rating for a 4 Ω load. At the same voltage, fewer ohms draw more current. The amp has to supply that current to maintain its output.
What might you notice when listening?
Some speakers make an amplifier work harder. If the amplifier can't keep up, loud passages may become distorted or trigger protection.
Should this affect what you buy?
Don't assume an amplifier with a big 4 Ω number can handle every difficult speaker. Follow the manufacturer's connection limits.
Go deeper: the technical explanation
By Ohm’s law, the same 4 V RMS gives 0.50 A into 8 Ω and 1.00 A into 4 Ω. Actual loudspeakers change their impedance with pitch and can introduce phase differences.
Distortion (THD)0.05% at a stated test level
In everyday language: A number describing extra sound the amplifier adds while reproducing a test note.
What might you notice when listening?
Enough extra sound can make music rough, buzzy or less clean. A very small printed percentage on its own doesn't tell you how the amplifier sounds throughout a song.
Should this affect what you buy?
Compare only when the test is described similarly. A figure at an easy volume is not the same as one measured near the amplifier's limit.
Go deeper: the technical explanation
Total harmonic distortion measures harmonics relative to a reference tone. The test frequency, output power, load, measurement bandwidth and distribution of harmonics can change its interpretation.
Background noise95 dB signal-to-noise ratio
In everyday language: How far above the amplifier's own hiss the music signal sits during a particular test.
What might you notice when listening?
More separation can help keep quiet passages free of audible hiss, although speakers, headphones and listening distance affect whether you'd notice.
Should this affect what you buy?
A large number is usually desirable, but only compare numbers measured under similar conditions.
Go deeper: the technical explanation
Signal-to-noise ratios depend on the chosen reference signal level and any frequency weighting. A-weighted and unweighted figures are not directly interchangeable.
Input sensitivity200 mV
In everyday language: How strong the signal from a music player needs to be for the amplifier to reach its rated output under a specified setup.
What might you notice when listening?
It's mainly about how easily the amplifier works with a music source, not a sound-quality score.
Should this affect what you buy?
Don't confuse this with the strongest signal the amplifier can safely accept. Many modern sources output more than 200 mV.
Go deeper: the technical explanation
Input sensitivity is the rated-output input requirement at a specified gain condition. Maximum input before overload is a separate quantity.
Frequency response20 Hz–20 kHz (±1 dB)
In everyday language: How evenly the amplifier passes along deep notes, voices and high notes.
What might you notice when listening?
An amplifier that changes certain notes more than others could alter the music's balance. Most properly functioning modern amplifiers are designed to stay very even over the main listening range.
Should this affect what you buy?
Look at how even the output is, not just how far the advertised numbers extend.
Go deeper: the technical explanation
The tolerance describes variation relative to a reference level over the stated range. Load, output level and measurement conditions affect the result.
Damping factor100 at 8 Ω
In everyday language: A number related to how much resistance the amplifier adds at the speaker connection.
What might you notice when listening?
It can affect the electrical interaction with a speaker, but it does not automatically mean punchier bass or better timing.
Should this affect what you buy?
A bigger damping factor is not always a meaningful audible upgrade. Real speakers and cables complicate the picture.
Go deeper: the technical explanation
The technical definition is the test load's resistance divided by the amplifier's output impedance at a stated frequency. It's a ratio, not a direct sound-quality score. A real speaker changes its electrical load across different notes, so one number cannot describe the full interaction.
PART TWO · LOUDSPEAKERS
What do speaker numbers tell you?
Deep bass, how loudly they play, and how demanding they are for an amplifier. These numbers can help, but one impressive specification never tells the whole story.
Frequency response55 Hz–20,000 Hz (±3 dB)
In everyday language: A guide to which low and high notes the speaker can play at roughly similar strength.
What might you notice when listening?
The speaker may handle voices and guitar well while the very deepest bass notes start fading. That doesn't mean the bass suddenly stops at 55 Hz.
Should this affect what you buy?
A frequency range without saying how much the output varies can be misleading. Room placement also changes the sound.
Go deeper: the technical explanation
A frequency-response range is normally tied to a tolerance relative to a reference level at specified measurement positions. A ±3 dB tolerance allows variation, rather than indicating perfectly flat output.
Bass extension45 Hz at −6 dB
In everyday language: How far the speaker reaches into the deepest notes before they become much weaker than the rest of the sound.
What might you notice when listening?
Think of the deepest notes on a bass guitar or a low movie effect fading while the song carries on at the same volume setting.
Should this affect what you buy?
A speaker that makes deep bass at a very weak level may still need a subwoofer if you want those notes to have strength.
Go deeper: the technical explanation
At a given measuring position and reference, −6 dB corresponds to approximately half the sound-pressure amplitude, not half the loudness you hear. The reference conditions must be specified.
Sensitivity87 dB at 2.83 V / 3.28 ft
In everyday language: How strongly a speaker plays when it's fed a standard test signal.
What might you notice when listening?
A more sensitive speaker may play louder at the same amplifier setting, although the actual result also depends on the amplifier and how the test was performed.
Should this affect what you buy?
It's useful for planning how much amplifier output you need, but it does not tell you whether the speaker has better bass, clarity or sound quality.
Go deeper: the technical explanation
At 2.83 V, a 4 Ω test load draws twice the current and receives twice the watts of an 8 Ω load. In this example that is about 2 W versus 1 W. Check which input the sensitivity rating uses.
Impedance6 Ω nominal
In everyday language: A rough label describing how much electrical work a speaker asks of an amplifier.
What might you notice when listening?
A difficult load can make some amplifiers run hotter, distort sooner or shut down at higher listening levels.
Should this affect what you buy?
Check that the amplifier supports the speaker's needs, and don't assume the number stays at 6 Ω for every note.
Go deeper: the technical explanation
A speaker's electrical load changes with the pitch of the music. Its lowest impedance and how far voltage and current move out of step (phase) can make it harder to drive than the single ohm figure on the box suggests.
Recommended amplifier power20–120 watts
In everyday language: The range of amplifier power the speaker maker suggests using.
What might you notice when listening?
A speaker doesn't constantly need that many watts to make music. A quiet listening session may use very little power.
Should this affect what you buy?
Don't treat the top number as a guarantee against damage. Very loud bass, a distorted amplifier or extreme settings can still damage a speaker.
Go deeper: the technical explanation
Power recommendations may reflect thermal and mechanical constraints, sensitivity, test procedures and marketing decisions. They are not a direct maximum-clean-output graph.
Woofer and tweeter5¼-inch woofer + 1-inch dome tweeter
In everyday language: Two parts that split the musical work: one handles lower sounds and the other handles higher sounds.
What might you notice when listening?
How the two parts blend can affect whether voices and instruments sound natural. Driver size or material alone doesn't settle that.
Should this affect what you buy?
Don't assume a bigger woofer always means deeper bass, or that a metal tweeter must sound sharp.
Go deeper: the technical explanation
Cone area, excursion, cabinet loading, driver resonances, crossover and dispersion interact to determine the speaker's behavior.
Crossover point2,400 Hz
In everyday language: The approximate place where one speaker driver hands more of the music over to the other.
What might you notice when listening?
A smooth handoff can help voices and instruments sound like one continuous sound instead of disconnected pieces.
Should this affect what you buy?
The number by itself doesn't show whether the handoff is well designed.
Go deeper: the technical explanation
Electrical filter settings and acoustic crossover behavior differ. Frequency, slope, phase and the drivers' off-axis output matter.
How widely sound spreadsCoverage: 90° (example)
In everyday language: How far the speaker is intended to spread sound to people sitting away from the centre.
What might you notice when listening?
Some speakers sound more consistent as you move to another seat, while others sound best in a narrower spot.
Should this affect what you buy?
Ask what notes and how much drop in strength the coverage number refers to. One angle doesn't describe everything.
Go deeper: the technical explanation
Off-axis response and directivity vary with frequency and are better assessed across multiple angles and acoustic measurements.
COMING AS THIS FEATURE GROWS
From simple answers to deeper understanding.
Additional specifications, original annotated graphs, interactive demonstrations, real product comparisons, and downloadable handbook-style PDFs will be added here as they are properly reviewed. The aim is to make the technical detail available without making it a barrier to learning.