LESSON 11 · HEADPHONES
Why can the same headphones lose bass?
A frequency range gives you the endpoints. The response curve shows the balance across that range, and the way the headphone sits can change the curve.
This example lists a frequency range without a level tolerance or test fixture. Read the example ↓
DECODE THE EXAMPLE
20 Hz–20 kHz
Synthetic curves, aligned at 1 kHz and plotted relative to the same example target.
What the rating tells you
20 Hz marks the bass endpoint. 20 kHz marks the upper treble endpoint. Both example curves cover the marked span, yet example B has 4 dB more output at 50 Hz in this level-matched comparison.
Those two frequency endpoints alone tell you nothing about whether bass, vocals or treble are emphasized. Even a claim such as ±3 dB needs a reference level and a clear way of measuring the headphone before you can judge how even it is.
Compare deliberate bass tuning with a pad leak
Try three versions: a closed-back headphone fitted properly, a different model deliberately tuned with extra bass, and the first headphone with a small gap between the ear pad and your head. That last gap can weaken deep bass even though the headphone itself has not changed.
Seated fit
The pad makes even contact
With the headphone seated, its response is close to the example target through much of the bass. At 50 Hz the curve meets the target.
This is the reference fit for the other two comparisons.
Bass lift
The second model adds bass by design
This headphone is 4 dB above the target at 50 Hz, with the response returning to the same level through the midrange.
Some people like the extra weight under drums and bass guitar. A consistent lift that follows the headphone across placements can reflect its tuning.
Pad gap
A leak changes the first headphone
The same closed-back headphone drops 8 dB at 50 Hz in this example, while the midrange stays close to its seated response.
A gap around glasses or hair can have this kind of effect. The size and shape of the change depend on the headphone and the leak.
Read the fixture and the reference line
A headphone measurement rig uses an ear simulator or an artificial ear to estimate the sound pressure near the eardrum. The fixture’s shape and acoustics influence the raw curve. The raw response of a well-tuned headphone will usually have visible rises and dips.
A compensated graph shows the difference from a chosen target. Its 0 dB line means the headphone meets that target at that frequency. Check which target and fixture were used before comparing two traces. Targets can encode different bass preferences, and one model can measure differently after it’s reseated.
An IEM’s tip and insertion depth can change the response too. Tip seal often matters most in the bass. In the upper frequencies, small changes in depth and ear geometry can shift peaks and dips.
Does the change follow the headphone or the fit?
If low notes come back when you reseat the pads or adjust an IEM tip, fit is a likely factor. If both channels have a repeatable bass lift with a good seal, you may simply prefer more or less bass.
Compare with the same passage at a matched midrange level. A kick drum and bass line you know can help you hear whether the change is concentrated in the low end.
COMMON CLAIM
“They reach 20 Hz, so they must have strong sub-bass.”
WHAT TO CHECK
Look at the response level near 20 Hz and how much it changes with different fits. Measurements from the same fixture, target and seating method give a stronger basis for comparison.
What should you look for?
- Look for a response plot that names its fixture, reference target and normalization method.
- Check repeated placements or fit-consistency results, especially if you wear glasses or are comparing IEM tips.
- Evaluate comfort and response together. Pads, tips and seal can affect both during a normal listening session.
Engineering deep dive Optional
A compensated curve can be written as the measured level at each frequency minus the target level at that frequency, expressed in dB. If the curves are normalized at 1 kHz, a constant offset aligns them at that reference. This keeps the graph focused on tonal balance rather than absolute sensitivity.
The synthetic pad-gap case changes only the low end to make the example easy to read. A real reseating can also change the angle and distance between the driver and ear, which can alter the midrange and treble.
Sources and further reading
- RTINGS · Headphone response and fit-consistency tests ↗
- miniDSP · Target curves and compensated measurements ↗
- Headphone Test Lab · Measuring pad leakage ↗
See where each pad or tip sits, or continue to headphone sensitivity and impedance.