LESSON 13 · HEADPHONES

Why can two headphone jacks sound different?

Ever used the same headphones on two devices and found that one sounds different, even after matching the volume? Sometimes a headphone jack changes the balance of bass, voices and treble. Here’s when that can happen, and when it probably won’t matter.

Headphone impedance
The headphone’s opposition to current. It can change from one note to the next.
Jack output impedance
How much the signal voltage drops inside the jack for a given current. A larger value means a larger drop.
EXAMPLE PRODUCT SPECIFICATION 10 Ω output impedance at 1 kHz

This is the jack’s own impedance, measured at 1 kHz. Read the rating ↓

DECODE THE EXAMPLE

10 Ω output impedance at 1 kHz

Before and after you plug in

At the 1 kHz test note, the jack in this example acts as if it has 10 Ω of resistance inside it. With nothing plugged in, the jack reads 1.00 V RMS.

Connect a 32 Ω load and about 0.76 V reaches it. Connect a 10 Ω load at the same setting and 0.50 V reaches it. The gold dots mark those two results.

The 1 V is the starting point for the example. To find how much clean volume the jack can deliver, check its output rating with a load connected.

Voltage at the load (V RMS) · 1 kHz 0 0.25 0.50 0.75 1.00 10 32 64 128 256 Connected load (Ω, log scale) 1.000 V with no load 0.500 V at 10 Ω 0.762 V at 32 Ω

Calculated voltage divider at 1 kHz with 1.000 V RMS open-circuit voltage and resistive loads.

Compare a bass note and a midrange note

Choose a case and see how much voltage reaches the headphones on each note. In the first two cases, the same headphone measures 48 Ω in the bass and 16 Ω in the midrange.

Voltage reaching the headphones · A full bar means 1.00 V RMS

0.98 V of 1.00 V
0.94 V of 1.00 V
Calculated examples. Each jack starts at 1 V RMS before the headphones are connected. The third case uses headphones with a steady 32 Ω load at both notes.

The two notes stay close

With a 1 Ω jack, both notes receive most of the available voltage. The headphone’s balance shifts very little in this example.

See the full frequency sweep in decibels Optional

The sweep follows the case selected above. Each trace is level-matched at 1 kHz. A rise shows where less voltage was lost than at 1 kHz.

Voltage change relative to 1 kHz (dB) 0 +1 +2 +3 20 100 1k 5k 20k Frequency (Hz, log scale) At 100 Hz: +0.35 dB

Why does the voltage drop?

In the example, the current passes through both the jack’s internal resistance and the headphone. Together they act like two resistors in one path. Ohm’s law says voltage drop equals current times resistance.

At the same starting voltage, fewer total ohms means more current. That current passes through the jack’s own resistance, so more voltage drops inside the jack and less reaches the headphone. In the two-note example, that happens on the midrange note.

A headphone's printed 16 Ω or 32 Ω is a starting label. The electrical load can rise or fall with different notes, just as a loudspeaker's can. A full impedance graph shows those changes; the box number hides them.

When could this happen to you?

Example 1: Earbuds and an older receiver. Some small in-ear monitors have several tiny speakers inside. If their electrical demand changes a lot between low and high notes, a headphone jack with a high output impedance can make the balance sound different. You may notice more bass or less treble, depending on the earbuds.

Example 2: The same headphones on two jacks. A dedicated headphone amplifier with a low output impedance may keep the tonal balance closer to what the headphones were designed for. An older receiver or a particular computer headphone output may behave differently. This depends on the actual jack and headphones, not whether the equipment is expensive.

Example 3: No problem at all. Many headphones have a fairly steady electrical demand, and many modern headphone jacks have a low output impedance. In those combinations, changing jacks may make little difference to the balance once you match the volume. Don’t buy extra equipment to solve a problem you can’t demonstrate.

Match the volume and listen to the balance

Keep the headphones and music the same, and match the volume before comparing jacks. If a jack reduces every note by the same amount, you mainly hear a volume change. If it reduces bass more than treble, or vice versa, the tone itself can change. The jack's output impedance is one possible reason, not proof of a fault.

COMMON CLAIM

“A higher-impedance headphone jack always sounds warmer.”

WHAT TO CHECK

Look at the headphone’s impedance curve. A high point in the bass can make the bass relatively stronger on some jacks. A high point elsewhere can change a different part of the sound.

What should you look for?

  1. Look up the jack’s output impedance and the headphone’s ohm rating. A small jack impedance relative to the headphone’s helps preserve the headphone’s balance.
  2. Look for a measured headphone impedance curve if available, especially with multi-driver IEMs. Large swings in ohms give the jack more opportunity to change the balance.
  3. Check whether the jack can supply enough clean volume. Listen for hiss with sensitive headphones.
Calculate the drop and check the one-eighth rule Optional

For the resistive example, Vload/Vopen = Rload/(Rsource + Rload). With a 32 Ω load, 32/(10 + 32) ≈ 0.762. At 100 Hz with the varying load, the ratio is 48/(10 + 48). At 1 kHz it is 16/(10 + 16). The ratio between those two gains is about 1.345, or +2.57 dB.

Real impedance can have both magnitude and phase. Use the complex impedance of the source and the load at each frequency, then take the magnitude of the voltage ratio. Under the simple resistive model, a 1:8 source-to-load ratio gives a gain of 8/9, about −1.02 dB relative to open circuit.

A practical rule of thumb is to look for a jack output impedance no more than about one-eighth of the headphone’s minimum impedance. A 16 Ω minimum suggests about 2 Ω or less. Use the actual impedance curve and output measurements when available.

Sources and further reading

For a real measured example, Stereophile’s explanation of headphone measurements discusses the Sony XBA-3iP in-ear headphones and shows why a changing electrical load can matter. Those are the author’s measurements; the interactive graph above is our own teaching illustration, not a graph of that product.

Revisit headphone response and fit for changes caused by the acoustic seal, or see how impedance affects speakers.