When you hear a voice between the speakers, a guitar stretching left, or drums behind the singer, much of that spatial picture may have been deliberately built in the mix. The loudspeakers and room determine how convincingly you hear it, but the original recording and the engineer's choices provide the cues.
Start with the simple idea: a mix decides how loud each instrument is and where it appears between your speakers. Explore those changes first; phase and advanced surround formats are deeper reading.
The central distinction: Recording captures or creates individual sounds. Mixing combines them into a performance with balance, space, tone and motion. Mastering then prepares and refines the finished mix. A more expensive amplifier cannot separate instruments that were irreversibly combined in a finished recording.
Imagine a made-up four-track recording: vocal, guitar, bass and drums. Select four mixing decisions applied to the same hypothetical sources. The dots show pan placement, and the lower plot shows fictional relative frequency energy, not a measured spectrum or an audibility test.
CHART OVERLAYS
Starting mix
All four parts compete near the center
All four stems are fictional and identical in source across the presets. We change only the drawn mix settings: position, broad level/EQ and optional ambience.
1. Where the four sources sit
Vocal · CenterGuitar · Near center (L 7%)Bass · Near center (R 3%)Drums · Near center (R 6%)
Each dot represents a mixer channel. Left/right position shows pan; vertical spacing only keeps labels readable and does not represent depth or measured distance.
2. Which bands compete
Overlapping colored lines illustrate potential frequency competition. There is no calibrated vertical dB scale, no psychoacoustic masking threshold, and no recreated musical waveform.
What this mixing choice can change
Centered parts can still be distinguished by timbre and arrangement, but similar-frequency material may mask one another.
A guitar and voice sharing the same midrange can make individual words or chord voicings harder to pick out.
This illustration does not prove the recording would sound congested. Performance, timing and playback affect the result.
Placement changed
Same four sources, redistributed left and right
All four stems are fictional and identical in source across the presets. We change only the drawn mix settings: position, broad level/EQ and optional ambience.
1. Where the four sources sit
Vocal · CenterGuitar · Left 82%Bass · CenterDrums · Right 56%
Each dot represents a mixer channel. Left/right position shows pan; vertical spacing only keeps labels readable and does not represent depth or measured distance.
2. Which bands compete
Overlapping colored lines illustrate potential frequency competition. There is no calibrated vertical dB scale, no psychoacoustic masking threshold, and no recreated musical waveform.
What this mixing choice can change
Panning adjusts relative left/right levels. It creates lateral positions without adding missing detail to a recorded track.
Bass and lead voice remain centered here, while guitar and a simplified drum stem move off-center.
Frequency overlap is still present. Panning can improve perceived separation in stereo but does not solve every masking problem.
Level and tone changed
Give overlapping parts more room in the mix
All four stems are fictional and identical in source across the presets. We change only the drawn mix settings: position, broad level/EQ and optional ambience.
1. Where the four sources sit
Vocal · CenterGuitar · Left 62%Bass · CenterDrums · Right 47%
Each dot represents a mixer channel. Left/right position shows pan; vertical spacing only keeps labels readable and does not represent depth or measured distance.
2. Which bands compete
Overlapping colored lines illustrate potential frequency competition. There is no calibrated vertical dB scale, no psychoacoustic masking threshold, and no recreated musical waveform.
What this mixing choice can change
The fictional guitar track is reduced through part of the vocal-presence band, while overall levels are rebalanced.
These are deliberately broad instructional choices, not prescriptions for mixing real guitars or vocals.
An EQ cut cannot recover musical information that was never captured. It can reduce competition among existing tracks.
Reflections / reverb added
Create a stronger sense of distance and environment
All four stems are fictional and identical in source across the presets. We change only the drawn mix settings: position, broad level/EQ and optional ambience.
1. Where the four sources sit
Vocal · CenterGuitar · Left 67%Bass · CenterDrums · Right 50%
Each dot represents a mixer channel. Left/right position shows pan; vertical spacing only keeps labels readable and does not represent depth or measured distance.
2. Which bands compete
Overlapping colored lines illustrate potential frequency competition. There is no calibrated vertical dB scale, no psychoacoustic masking threshold, and no recreated musical waveform.
What this mixing choice can change
An early reflection or short delay can suggest a reflective space. Reverb decay helps define a sense of distance.
Our dotted halos represent an added effect, not measured reflections in the listener's room.
Heavy reverb can also blur timing and separation. A wider picture is not automatically a clearer picture.
The four musical parts are not real audio stems and this demonstration does not play copyrighted or synthetic music. Panning and EQ choices are fictional examples, not claims of measurable effects in a particular studio. The spectrum curves are intentionally schematic. Hiding a trace is a visual overlay control, not a mute that recomputes the mix.
Balance and masking
An engineer can lower a loud guitar, adjust a vocal's presence range, automate a bass line or change the arrangement so fewer parts compete. Overlap on a frequency plot indicates only potential competition, not proven masking or audible congestion.
Depth, movement and energy
A voice can seem close when you hear mostly the direct sound, or farther away when you hear more echo and room reflections. Small delays, changing instrument positions and programmed volume moves (automation) can create movement. Processing the first hit of a sound (its transient) or controlling the whole mix's level with compression can also change its impact. Wider is not automatically better.
MIXING CLOSE-UP · THE ENERGY OF EACH PART
A steady guitar. A punchy snare. The same song.
The finished song isn't one giant recording from the start. While mixing, an engineer can work with the separately recorded instruments. A guitar can remain steady underneath the music while a snare still jumps out of the band. Even different microphones around one drum kit can be treated differently.
What does compression mean here? Imagine turning down the strongest notes of one instrument, so those notes don't tower as far above its quieter moments. The engineer can then bring the track up to make its quieter body easier to hear. They don't have to make the same choice for every track.
One imaginary band, four separate recordings
Switch between the same short musical passage before and after individual track choices.
0 sec1 sec2 sec3 sec4 sec
Rhythm guitarChords and sustain
Bass guitarNote attack and body
Snare microphoneDrum hits and ring
Cymbal / overhead microphonesShimmer and decay
These fictional tracks have different amounts of control, rather than one effect applied equally to all of them.
Inspired by an audio editor's multitrack view. These waveforms are generated illustrations of a musical phrase, not samples from a commercial recording or measured compressor output. Each instrument keeps the same display scale before and after; differences in height across separate instrument rows do not establish which instrument sounds louder. Taller peaks or a denser shape alone cannot tell you how good a mix sounds.
Why treat instruments differently?
Guitar and bass: a steadier level can hold the rhythm together without competing with every drum hit. A heavily distorted electric guitar may already have reduced dynamics from the distortion itself. It might not need another heavy compressor.
Snare: the engineer can control an unusually loud hit, bring out the drum's ring or let its first crack through. How quickly the compressor reacts changes the result, so compression does not always mean less punch.
Even one drum kit isn't one track
Cymbals: overhead microphones can be left more open so the crashes rise and naturally fade, while a separately recorded snare microphone gets more control.
Important limitation: microphones often pick up more than one part of the kit. Snare can spill into overheads and cymbals into the snare mic. They are not perfectly isolated, and a single pre-mixed drum recording offers less freedom.
How this connects to mastering: the engineer blends these differently treated tracks into a finished stereo mix. The mastering lesson compares three versions of that whole mix. More compression on the finished song can change how much the snare stands out against the already steady guitar and bass, even though their individual mixing choices were different. Turn a quieter, more dynamic master up for a fair listening comparison; the extra contrast is already in the recording, not created by the volume knob.
02 / TIMING AND MONO
Why can a wide mix sound thin in mono?
Picture two microphones on the same snare drum. Sound reaches the closer mic first. If the engineer puts one recording on the left and the other on the right, the snare may sound wide. Switch to mono and those left and right signals blend into one. The little timing difference can change the snare’s tone.
Look at one part of the sound at the same instant. Two wave peaks can reinforce each other. If a peak in one copy lines up with a dip in the other, that part gets weaker.
The waves line up
Mic 1Peak
Mic 2Peak
In monoStronger
A peak meets a dip
Mic 1Peak
Mic 2Dip
In monoWeaker
Phase cancellation is what engineers call that weakening. It can affect several pitches at once, which can make the snare sound hollow or lose some of its snap. A series of dips in the tone is called comb filtering.
Try it by ear. If you can switch a mix to mono, listen to the snare or a guitar as you switch back and forth. Listen for a change in the tone as well as the smaller sense of space. When recording, moving one mic or blending in less of it can help if the sound gets thin.
See which pitches get quieter
Try the two delays, both about a thousandth of a second or less. The dashed blue line shows the mics lined up. The gold line shows what you get when you blend the two recordings. Each dip is a part of the sound that got quieter. The low pitches are on the left and the high pitches are on the right.
Both copies line up. The gold line follows the blue reference, so the tone stays the same.
A delay of 0.25 ms makes the first dip near 2 kHz. That can change the snap of the snare.
With a 1 ms delay, the first dip moves down to around 500 Hz. That can take some body out of the snare.
The example blends two identical recordings at equal volume. Real microphones can hear different levels and room reflections, so the dips can be shallower.
03 / IT ISN’T ALL THE SAME STEREO
One sound, five ways to place it
Follow the same shaker hit from your listening seat. Switch between the examples to see where the hit plays, where it may seem to come from, and what creates that impression.
Pan the hit toward the right speaker
From above · front of room
LeftLess of the hit
RightMore of the hit
You
Physical speakerWhere you may hear the hit
How it’s placed
The engineer sends more of the hit to the right channel than the left. That control is called panning.
What you may hear
From a seat between the speakers, the hit seems to come from the front-right, somewhere between them. Sending the same sound equally to both speakers can put it in the middle. That’s the phantom centre.
Playback
Two speakers or stereo headphones. The map shows the speaker version.
Give each ear its own version of the hit
From above · front
You
Left ear A little laterRight ear First
Shaker hit
Your headphonesWhere you may hear the hit
How it’s placed
Two mics in a model head can record what each ear would hear. Software can also work out those differences in timing and tone.
What you may hear
The ear closer to this hit gets it first. The head and ears also change how it sounds. On headphones, those clues can make the hit seem to come from just behind your right shoulder.
Playback
Headphones keep the left and right ear signals separate.
Make the hit seem farther out than the speakers
From above · front of room
Left
Right
Both speakers play the processed mix
Seems here
You
Physical speakerWhere you may hear the hit
How it’s placed
The engineer applies QSound to the hit and records the result into the left and right channels of the release.
What you may hear
The hit can seem to come from past the right speaker, even though the sound comes from the two speakers shown. Where you sit and how the speakers are set up can change the illusion.
Playback
Two speakers, with your seat centred between them.
Send the hit to a speaker beside you
From above · front of room
Left
Centre
Right
Subwoofer
Left surround
Right surround
Hit plays here
You
Physical speakerWhere you may hear the hit
How it’s placed
The engineer sends the hit to the right surround. A 5.1 mix has separate left, centre, right and two surround channels, plus a bass-effects channel.
What you may hear
You can hear the hit from beside or slightly behind your right shoulder because a speaker there plays it. Other sounds can stay up front at the same time.
Playback
A 5.1 mix played on five speakers and a subwoofer, as shown.
Move the hit from in front of you to above you
From the side
Height speakers
Front speaker
Surround
Start
Overhead
You
Physical speakerWhere you may hear the hit
How it’s placed
The engineer can give the hit a position and change it over time. The sound and its position are stored together as an object. The rest of the mix can also use groups of channels called beds.
What you may hear
Here the hit repeats as it moves upward. A compatible player uses the speakers it has, including height speakers in this setup, to follow that move. It can also create a version for headphones.
Playback
An Atmos mix and compatible playback. The side view shows an example with height speakers.
Where you hear the hit depends on the mix and your listening setup, including your seat, room or headphones. The album examples below point to specific releases that use these approaches.
04 / HEAR THE IDEA IN EXISTING RELEASES
Real albums that took different spatial approaches
These are edition-specific research and listening references. We link to credits or release documentation, not to unlicensed audio. They also illustrate why a new surround mix is not simply the same stereo master at a higher resolution.
Original U.S. Columbia CD CK 47127 is documented as a QSound stereo release. The 2015 reissue includes a distinct 5.1 surround mix; don't confuse the versions. Many spatial sound effects were intentionally placed during production.
Compare: original 1992 QSound stereo versus the separately mixed 2015 surround edition.
Contemporary Sire/Warner advertising calls out QSound processing on the 1990 greatest-hits collection. It demonstrates processed stereo spatial presentation without requiring discrete surround speakers.
Look specifically for the original compilation mixes, not a similarly named single or unrelated compilation mastering.
The album's release commentary discusses Tchad Blake's binaural recording approach. Do not assume every instrument or every song was recorded with the same dummy-head configuration.
The word binaural describes a production approach here, not a guarantee of any particular headphone effect.
Wilson's 2013 deluxe Blu-ray already included a 96 kHz/24-bit 5.1 mix. The distinct 2026 Headphone Dust edition adds a new Atmos mix and a binaural stereo edition alongside stereo and 5.1 versions.
Mic pickup, pan positions, room reverberation, stereo correlation and spatial processing determine which cues are in the master. Speaker placement and the listener's room determine how those cues unfold.
Arrangement, levels, spectral masking, timing, saturation and bus dynamics influence whether simultaneous sources remain distinguishable. A good amplifier cannot unmash a flattened mix.
Relative voice/guitar levels, spectral shaping, mic proximity and reverberant balance may encourage these descriptions. They are not universal measurements or the exclusive properties of headphones or speakers.
How hard the musician plays, the shape of the first hit, and how quickly a compressor turns the sound down and lets it recover all affect punch. Engineers can also ride levels during the song (automation). The mastering lesson shows how those loud-and-quiet contrasts can change after the instruments are combined.
The honest boundary: playback components can add measurable coloration or processing, and some DSP can construct new spatial effects. They cannot reliably recreate missing source tracks, the precise unrecorded room or transients deliberately removed from the final mix. A spacious mix still needs reasonably suitable playback for its spatial intentions to translate.
NEXT: THE FINAL RELEASE
What happens to the mix before release?
Compare three masters of one performance in Lesson 23. See how the tone, drum hits and average level can change, and find out why the LP, CD and stream of an album can sound different.
The stage, energy curves, phase calculation and format diagrams are original teaching illustrations. No third-party plots, image assets, source recordings, copyrighted multitracks or audio effects have been copied. Source links support the named production concepts and release-specific examples.
Editorial review 12 November 2026. In practice, a soundstage is an interaction among source, production, recording, playback chain, speaker layout, room and listener, not a single guaranteed measurable property of a song.